Restoring the official firmware of ASUS RT-G32 ver. C1. “Here’s an Asus RT-G32 C1 - make a router out of it” or WIVE-NG-RTNL firmware for RT-G32 C1 Let’s move on to the firmware - a simple procedure
The other day after an unsuccessful distributor firmware ASUS RT-G32 (ver. C1) The device completely refused to work. It was impossible to even enter the device management page (I mean addresses 192.168.0.1 or 192.168.2.1 ). Tips on forums about restoring factory firmware using the program tftpd32 didn't help. To be honest, I began to fear that I would no longer have Wi-Fi and began to figure out in my mind what would be more profitable - to give my Asus to a workshop or to buy a new network distributor. However, the situation was alleviated by the leadership from one foreign network (the link will be below) - I’m translating the sequence of actions into Russian.
Note before you start - you will need O. With. Windows to perform these actions; For Linux, unfortunately, there is no manual.
No wireless device in recovery mode is found, firmware ASUS RT-G32 ver. C1, Asus Firmware Restoration, asus firmware 2.0.3.4, router, router, wifi, wifi
So:
1. Download the archive with the recovery program Asus Firmware Restoration and manufacturer's firmware ASUS_2.0.3.4(urgently on October 17, 2015):
2. Extract the contents of the archive, say, to the desktop;
3. Then connect the device directly to the network card - connect one end of the network multi-core (cable) to the computer, and the other to the connector LAN1 router (modem, if available, turn off for a while);
4. Enter the Network and Sharing Center (tray icon):
5. Click "Change adapter settings":
6. Disable all interfaces except "Local Area Connections" (LAN):
7. Open interface properties LAN:
9. Disable firewall Windows in the control panel (as shown in the picture), as well as third-party firewalls (Kaspersky, Komodo, Outpost, Avast, Nod32...):
The first part of the preparation is completed, and now the second part, the recovery itself:
10. Launch the program Rescue.exe from the previously unpacked archive and indicate in it the path to the firmware file RT-G32.C1_2.0.3.4.trx, But IN NO CASE Don't press the button yet Download":
11. Check again that all wires (cables) are disconnected (including the power cord). Only the network multicore connecting the connector should remain LAN1 router and computer network card slot;
12. Press the button with a toothpick or ballpoint pen. Reset- press and hold until you release:
 |
| I took this picture from the page |
If you recently became the owner of an Asus RT G32 router and encountered certain problems during its connection and configuration, then you have come to the right site. In this article we will look at the most common problems that you encounter when setting up this router, and also tell you about some operating tricks.
First, you must definitely ask your provider for the following configuration features that will be entered directly during setup: protocol (PPTP, L2TP, PPPoE), IP properties (static or dynamic, automatic or manual assignment of IP and DNS), as well as the presence (or absence) binding the network card by MAC address. It also wouldn’t hurt to find out if a special login and password have been set for logging into the router’s control panel.
In the next step, our path lies in the properties of the local network connection (Control Panel - Network and Sharing Center - our Internet connection - left-click on it - Properties). We look for “Internet Protocol Version 4 (TCP/IPv4), click on “Properties.” In the “General” tab, click “Obtain an IP address automatically” and “Obtain a DNS server address automatically.” Click “OK.”
At this point, you should already have an Ethernet cable connected from your computer to the router, into the LAN 1 connector. It is recommended to reset the settings before the first setup - this is done very easily: press the Reset button for 10 seconds.
The site will require authentication - login and password. If your provider does not set any specific data, then enter the standard ones - admin in the login and admin in the password. You can also find information on the login and password from the router control panel on the bottom of the router.
After all the operations, we find ourselves. First of all, indicate the protocol of your operator on the “WAN” tab in the “WAN connection type” line. If the address is provided automatically, we leave everything as is. If you need to register the IP address and DNS manually, then check the “No” box in “Obtain a WAN IP address automatically?” and enter the parameters below.
The main part setup is complete. Now - setting up WiFi. This is the "Wireless Network" - "General" tab.
- SSID - the name of your router;
- Hide SSID - whether you need to display the router name or not;
- Country code - select your country;
- Wireless network mode, Channel width - leave as is;
- Channel - it is advisable to set something other than automatic or the first - optimally 6 or 9. This setting will help you speed up your wireless Internet connection;
- Expanded channel - leave it as is;
- Authentication method is WEP, WPA or WPA2. The most modern is WPA2, so we install it. The rest of the settings are default.
You can also enter your own password in the WPA Pre-Shared Key field. That's all on this page - you can click "Apply".
Now go to “Administration”, where we click “Reboot” and “Exit”. The router will be completely ready for use after a reboot.
This is all we wanted to tell you about setting up a router of this model. If you have any questions, ask them in the comments and we will definitely answer them. See you on the pages of our website!
Firmware 1.0.4.1 provides support for IPTV in all modes (udp-multicast, udp-to-http proxy, STB-port). IPTV has been tested on the Ukrtelecom network. Allows the use of Ethernet WAN.
XWireless router and ADSL modem
Firmware 1.0.4.1 provides support for IPTV in all modes (udp-multicast, udp-to-http proxy, STB-port). IPTV has been tested on the Ukrtelecom network. The firmware also supports working with 3G modems.
X
Dual Band Wi-Fi Router
Firmware 3.0.0.4.314 (Annex A) with support for 3G modems and full support for IPTV Ukrtelecom.
Firmware 3.0.0.5.374 (Annex A) with support for DUAL WAN, 3G modems and full support for IPTV Ukrtelecom.
Wireless N Router with EZ UI
Firmware version 2.0.3.2 for the RT-N10 B1 router has increased WAN-LAN throughput.
X
802.11n 150 Mbps wireless router with a powerful 5 dBi antenna to increase wireless network coverage.
Instructions for setting up a network printer or MFP
Firmware 7.1.1.1.32b
Wireless router standard 802.11n 150 Mbit/s with a powerful 5 dBi antenna to increase wireless network coverage. With firmware version 3.0.0.3.135 supports 3G modems.
Firmware 3.0.0.4_374_5517 with support for 3G modems
Firmware 3.0.0.4.260 with a new interface and support for 3G modems
Firmware 3.0.0.4.321 with a new interface and support for 3G modems
Router, access point and repeater in one device. Two removable antennas with a gain of 5 dBi. Created according to the 2T2R scheme, it provides a high data transfer rate of 300 Mbps.
Firmware for ASUS RT-N12 D1 3.0.0.4.374.430
Firmware for ASUS RT-N12 D1 3.0.0.4_374_4230. Improved speed on PPPoE connections.
Firmware for ASUS RT-N12 D1 3.0.0.4_374_4583
Wireless N router with integrated print server
Firmware 2.0.2.5o for RT-N13U B1.
7.5.1.98 - supports 3G modems of all Ukrainian 3G communication operators and the 802.1x Ethernet authentication protocol via the router’s WAN port.
Wireless router RT-N15U Wi-Fi 802.11n standard (300 Mbps), equipped with Gigabit Ethernet ports and designed for use at home or in a small office.
Firmware 3.0.0.4_374_4583
Firmware 3.0.0.4.260 with support for 3G modems
The latest firmware for RT-N15U.
Multifunctional N-standard wireless router with file, print and media server capabilities
Firmware Version 3.0.0.4.315 - new interface design, support 3G/4G (Freshtel, Giraffe), AiCloud
Firmware Version 3.0.0.4.321 - new interface design, support 3G/4G (Freshtel, Giraffe), AiCloud
